Graham Nash

unfortunately work is getting in the way for me today. The fog was pretty thick this morning when I walked the dogs. Good luck anyone heading out.

I had fully intended on taking the boat out of the water to start ripping the deck up but i keep seeing a potential weather window later this week. Is anyone else seeing the same and thinking of getting out?

That looks like a huge job Charlie. I've seen your boat many times (I've even been out on it). I never realised you had done the build! Fantastic and no wonder you're so pleased with her.

is that Swahili you were writing Jim?

Cardboard Aided Design very good 😄

what is?

Thanks Charlie, Im sure a few of us would love to see some of your build pictures. I am not sure what I need to do below the deck yet, but Im expecting to need to do the stringers in both planes. Good idea about making a cardboard template, I throw loads of very large sheets of cardboard away from my work.

oh what fun indeed!! Thanks for that Charlie (I think). I have no bulkheads to do, just a relatively small deck and potentially the stringers. The nidalplast I have been quoted for is either 1.2 X 1.2 square or 2.4 X 1.2 but they seem to want to sell the larger sheets in quantities of 5 (which Im not sure I'll use). Probably if I was dong the stringers from Nidaplast I could use that quantity, but I was expecting to need to do the stringers from marine ply to enable me to screw the deck into it.

Taken from one of the boat maintenance forums ive been reading ...... "The problem is that Nidaplast is a honeycomb material, so I cannot use screws to fasten it to the stringers, as this wold crush the honeycomb material". I believe I can stick it down and use screws to hold it while the glue dries, but i assume I would need ply stringers (or ply attached to the side of the nidaplast stringers) to screw into. Im hoping someone on here will have done one so I can learn from their mistakes :-)

That's my understanding.

speaking with East Coast Fibreglass they suggest two layers of 800g on each side and it is almost impregnable (and completely rot resistant). But theres nothing to screw into for deck fittings (like seats and consoles etc) so Id guess I would need a certain amount of wood underneath for fittings etc?

I love it 😂😂

I replaced a bit of spongy deck last spring. While cutting it out i found it to be pretty damp under there and the foam was wet. I fully intended on doing the whole lot this winter/spring. I intend getting the boat out of the water in the next week or so and removing the existing deck, foam and stringers (if required). Ive spoken on a number of boat forums and there seems to be a big following of "nidaplast". I spoke with East Coast Fiberglass Supplies and the guy there says he has worked with Nidaplast and he loves it. I see Mike Hall (club member) recently had a Wilson Flyer for sale with a new nidaplast deck and transom. Ive done a deck before using marine ply and it was fine for the couple of years that I had it. Does anyone have any thoughts or experience of doing the same? Any advice would be gratefully received. Thanks Graham

Mike, good luck with the sale (if its still about). Im looking at doing the same with my Orkney 590. How did you find working with Nidaplast?

Thank you Allan. Ill call you.

sounds like just what I need. How do we arrange drop off?

Unfortunately I could only choose between the 29th and 30th. Both of those are looking very unlikely so Ill make my call now that I wont be joining you I'm afraid. (I've never caught a cod from my own boat anyway so I doubt I would have been any competition anyway).

I popped out last Sunday in a little window. There was still lots of swell left over from the previous days and wind against tide made it a quite uncomfortable (and short) trip

if anyone can catch a cod my money would be on you Nigel

Im hoping to be out on Samoya probably the 29th (Ill confirm before I go)

have fun guys. Unfortunately work is getting in the way of my fishing

This is good to know. I have a few reels that could be doing with a look at. I wasnt sure whether to get them fixed or not. Ill look them out and give you a message to see if you think they are worth fixing.

It's yours if you want it Jerry. My number is 07710911921, I'll be trying to make the next club meeting on Tuesday if you're there or we can arrange something else.

I have 60 met of 16mm rope taking up space in my garage. Available to anyone who can use it, for a donation to the charity of your choice

I hope it's on, I've spent this afternoon renewing my line on my reels with heavier line after losing three heavy fish last weekend.